Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the pro arrives.
Get your free estimateTrusted Garage Door Opener Repair for St. Louis Homeowners
A garage door opener that quits is a daily problem, not a someday problem. If yours hums without lifting the door, reverses halfway up, or refuses to respond to the remote, the fix usually comes down to a few known failure points: the drive gear, the logic board, the safety sensors, or a travel limit that has drifted out of adjustment. We work on what you already have. Our technicians have up to 14 years of experience and are fluent in the openers most St. Louis garages actually run on, including LiftMaster, Chamberlain, Genie, and Craftsman systems. That matters in a city where so many homes still carry original equipment from a builder installation and the homeowner wants the opener repaired, not replaced on the spot. We offer same-day service when you call, and your price is quoted and agreed before any work starts. Call (866) 942-7683.
Garage Door Opener Installation
Garage Door Opener Installation is the job of mounting a new unit, aligning the rail to the door’s travel, wiring the safety sensors, and pairing every remote and wall control so the system works as one. You need it when an opener has no repair path left, when you’re adding a door to a garage that never had one, or when you want smart-home control that older units can’t provide. Landon Garage Door Repair handles the whole install: the unit, the mounting, the safety reverse check, and the final calibration so the door stops where it should. Installation typically runs $250 – $550, depending on the drive type and what wiring the garage already has. The written estimate sets the final price, and we measure and schedule rather than rushing a same-day job.
Choosing the Right Drive Type
Chain and belt drives both pull the door from above, but they differ in noise and upkeep. Belt units run quieter and suit bedrooms above the garage; chain units cost less and take more wear without complaint. We’ll walk you through the tradeoffs for your door’s weight and your ceiling height before anything is ordered.
Safety Reverse and Sensor Checks
Every install finishes with a physical test: the door should reverse on contact with an object and the sensors should trip when the beam is broken. St. Louis garages often have low clearance and offset framing that make sensor alignment fussier than the manual suggests. We adjust the brackets so the beam clears the door’s path instead of lining up by eye.
Styles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
Garage Door Opener Replacement
Garage Door Opener Replacement means swapping out a failed or outdated unit for a new one that matches your door. It’s the right call when the motor is burned, the logic board is obsolete, or the repair cost heads toward the price of a fresh unit. Because we also handle Landon Garage Door Repair work on panels, springs, and tracks, we can tell you honestly whether your opener is worth saving or whether replacement is the smarter money. Replacement typically runs $250 – $550 including the unit and the labor to mount and calibrate it. We’ll quote it in writing before we start, so there’s no surprise when the work is done.
Repair Versus Replace
Most opener faults – a stripped gear, a dead capacitor, a remote that won’t pair – are cheap to fix and worth fixing. We compare the repair price against a replacement quote and give you both numbers. You decide; we don’t push the more expensive path.
Matching a Unit to Your Door
A heavy Clopay or Amarr door needs an opener rated for its weight and balanced properly first. We check the door’s spring tension before installing anything above it. A new opener on an unbalanced door wears out fast, and we’d rather solve that now than sell you a repeat visit.
Garage Door Remote Programming
Garage Door Remote Programming is the process of pairing remotes, keypads, and vehicle buttons to your opener so they open the door reliably. You need it when you buy a new remote, move into a home with unknown remotes still floating around, or find a button that has to be held at the perfect angle. We clear old codes from the opener and program fresh ones for every remote you keep. Programming runs $120 – $320 depending on the number of devices and how the opener handles its learn button. If your system uses MyQ or another Wi-Fi bridge, we pair that too, and the written estimate locks the price before we begin.
Clearing Old Codes
When you move into a St. Louis home, the previous owner’s remotes and any spare keypad codes may still be stored in the opener’s memory. We wipe the memory and re-add only the devices you want. That’s a small job with a real security payoff.
Wi-Fi and Smart-Home Pairing
Newer openers link to a phone app through a bridge or built-in Wi-Fi, and the setup trips up a lot of homeowners. We pair the network, confirm the app controls the door, and test it from outside the garage. No guessing at passwords or firmware.
Garage Door Opener Battery Replacement
Garage Door Opener Battery Replacement covers two separate batteries: the backup battery inside the opener that lifts the door during a power outage, and the coin cells inside remotes and keypads. You need it when the door won’t open during a blackout, when a remote only works up close, or when the opener beeps to signal a dying backup cell. We test both before replacing, so you don’t pay for a battery that was never the problem. Battery service typically runs $120 – $320, and we confirm what’s needed with a written estimate before any work starts. Our technicians carry the common backup packs for LiftMaster, Chamberlain, and Genie units.
Backup Battery Age
Backup batteries lose capacity over time even when they never run the door. If yours is several years old and the opener beeps or won’t lift during an outage, a replacement restores that safety net. We check the charge and the terminals while we’re in the housing.
Remote and Keypad Cells
Remote batteries fade slowly, so a button that needs several presses reads as a signal problem. Fresh cells and a quick programming check usually solve it. We replace the cell and verify range from the street before we leave.
Garage Opener Maintenance
Garage Opener Maintenance is a tune-up of the opener and the door it drives: tightening the chain or belt, checking the force settings, lubricating the rail, testing the safety reverse, and confirming the springs still balance the door. It’s worth doing once a year or whenever the door starts sounding different. Landon Garage Door Repair handles the opener and the door hardware together, so a maintenance visit catches wear before it becomes a repair bill. Maintenance on the opener typically runs $120 – $320, with the written estimate setting the price. We don’t sell annual plans; we quote the work each time you call.
Checking Force and Travel Limits
Force settings that are too high let the door crush an obstruction instead of reversing; too low and the door stalls halfway. We measure both and reset them to spec. That’s a safety adjustment, not cosmetic.
When the Door Needs Work Too
An opener straining to lift a door is often a door problem, not a motor problem: a worn roller, a spring that has lost tension, or a track out of alignment. We check those on the same visit. One call covers both ends of the system.
Garage Door Opener Not Working
Garage Door Opener Not Working is a broad symptom with a short list of causes: no power at the outlet, a tripped breaker, misaligned safety sensors, a broken drive gear, a dead logic board, or a remote that lost its programming. You need a technician when the easy checks don’t clear it and the door stays down. We diagnose the actual system in front of us rather than running down a generic checklist. Opener repair typically runs $120 – $320 depending on the failed part, and we give you the written price before we touch anything. Same-day service is available, and we answer 24/7.
The Common Failure Points
Genie and Craftsman units are known for stripped drive gears; LiftMaster and Chamberlain boards are common culprits on no-response calls. Sensor misalignment is the most frequent cause of a door that runs partway and reverses. We test each in order so you pay for one diagnosis, not several.
What to Check Before You Call
Look at the wall outlet and the breaker, and clear anything blocking the sensor beams on either side of the door. If the opener still doesn’t respond, call us. We’d rather you skip the ladder and the guesswork on the electrical side.
Garage Door Motor Replacement
Garage Door Motor Replacement is the swap of a failed motor inside the opener housing, or a full unit replacement when the motor takes the board and gear with it. You need it when the motor runs hot, grinds, or fails to lift the door at all after other causes are ruled out. We test the motor under load before recommending a swap, because a screaming opener is often a door balance issue instead. Motor work falls within opener repair at $120 – $320, and replacement of the whole unit sits in the $250 – $550 range. The written estimate settles the number before we start, and our technicians have up to 14 years of experience on these drive systems.
Telling a Motor From a Door Problem
Disconnect the door from the opener at the release and lift it by hand. If it’s heavy or won’t stay up, the springs or balance are the real problem. We run that test before quoting a motor swap.
Why We Don’t Skip the Diagnosis
Replacing a motor on a door that’s out of balance just buys you the same failure on a new unit. We fix the door first when that’s the cause. The goal is the right fix, not the most expensive one.
Brands We Service
We service LiftMaster and Chamberlain equipment, two of the most common openers in St. Louis garages, and we know where those units wear out: the drive gear and the logic board are the usual failures. Craftsman openers, which share a lot of the same internals, get the same treatment. On the door side, we work on Clopay and Amarr doors and understand how each maker’s panels and hardware behave when the opener is struggling to lift them.
Wayne Dalton and Raynor round out the list, along with Genie. Each one has quirks in how it pairs remotes, handles safety sensors, or sets travel limits, and we adjust to the system rather than sticking to one brand’s playbook. Whether you have a Genie opener on a Wayne Dalton door or a LiftMaster driving a Clopay panel, we can help. No brand is off-limits within our confirmed list, and we never steer you toward a product line for commission’s sake. If you’re in Clayton or University City and want the same opener expertise closer to home, our garage door opener repair page covers that area.
See the difference
Before
After
Before
After
Before
AfterSigns You Need a Pro Right Now
- The door reverses before it closes. That’s usually a sensor or a travel limit problem, and it can leave the house open to the weather and to anyone walking up. Safety sensors need a proper alignment check, not a piece of tape over the lens.
- The opener hums but the door doesn’t move. A hum with no lift points to a stripped gear or a burned capacitor. Running it longer can seize the motor, so have it looked at before the damage spreads.
- You hear a snap and the door won’t lift. A snapped spring is a separate failure, and it’s dangerous to touch. The springs and cables are under high tension and should only be handled by a trained professional.
- The door doesn’t open during a power outage. A dead backup battery is the usual cause. It’s a small repair that restores the door’s function when the power is out.
- The door opens on its own or a button only works up close. That can be a stray code, a failing remote cell, or an opener board problem. Clearing the codes and testing the range settles which.
Our Process, Step by Step
- 1
Listen and diagnose. We start with your description, then run the door and watch the opener’s response. Force settings, travel limits, and sensor alignment are checked first, because those catch the most calls.
- 2
Isolate the failure. We release the door from the opener and test it by hand. If the door is heavy, the problem is balance, not the motor. If it lifts freely, the fault is electronic or mechanical inside the opener.
- 3
Quote in writing. You get the number before any work starts: the part cost and the labor, itemized. If the diagnosis changes once we’re inside, we stop and requote rather than adding charges later.
- 4
Repair with the right part. We match the part to your system, whether it’s a LiftMaster board or a Genie gear. We don’t substitute a generic part that fails again in a year.
- 5
Test and confirm. The door runs through a full open and close, the safety reverse trips, remotes and keypads work from the street, and we walk you through what we found. No loose ends.
How Much Does Garage Door Opener Repair Cost in St. Louis?
Garage door opener repair in St. Louis typically runs $120 – $320, depending on the failed part and how deep the fix goes. A sensor alignment or a remote reprogramming sits at the low end; a logic board swap pushes toward the top. Remote and battery service also falls in that range, and motor replacement rides with it. When the whole unit needs to go, opener replacement runs $250 – $550, and a new install lands in the same band.
What moves the number: the brand and model, the part availability, whether the door itself needs a balance or spring fix, and whether you’re dealing with a smart-home bridge or older wiring. Older homes in Webster Groves and Crestwood sometimes have opener wiring run through unfinished garages, which can mean a bit more labor to trace a fault. A newer install in Overland is usually quicker to diagnose.
How to avoid overpaying: get a written estimate before work starts, ask whether the diagnosis cleared the door’s balance first, and skip anyone who quotes a new unit before checking the repair path. Our estimate is free, and it includes the diagnosis, the itemized part and labor, and a plain answer on whether repair or replacement is the smarter money. The price we quote is agreed before we touch the opener, and the written estimate sets the final price.
Our Service Area Near St. Louis
We serve St. Louis and the surrounding communities, including Clayton, University City, Jennings, Webster Groves, Lemay, Affton, Overland, Bellefontaine Neighbors, Ferguson, Crestwood, and St. Ann. Opener calls are often handled same-day, and we answer 24/7 with fast dispatch from 7am to 7pm, Sunday through Friday. If you’re in University City, our garage door opener repair page covers the area, and for full-system work see garage door opener repair.
Serving St. Louis, MO – Our Local Coverage Area
We serve St. Louis and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Garage Door Opener Repair in St. Louis
Garage door opener repair is the diagnosis and fix of the motorized unit that lifts and lowers your door, including the motor, drive gear or belt, logic board, safety sensors, remotes, and power supply. It’s separate from door repair, which covers the panels, springs, tracks, and cables. We handle both, so a fault at one end doesn’t send you to a second company. Call (866) 942-7683 for a free estimate.
Most opener repairs finish in a single visit, often within an hour or two once we’ve diagnosed the fault. Simple fixes like sensor alignment or remote programming are quicker; a motor or board swap takes longer. We’ll tell you the expected time when we set up the visit. Call (866) 942-7683 to book it.
Typical opener repair in St. Louis runs $120 – $320, and installation or replacement runs $250 – $550, depending on the part and the labor. The written estimate sets the final price, and you approve it before any work starts. Call (866) 942-7683 for an exact quote – estimates are free.
Yes. We service LiftMaster, Chamberlain, Genie, Craftsman, and the other common residential brands, along with doors from Clopay, Amarr, Wayne Dalton, and Raynor. We diagnose the specific system in front of us rather than working from a generic template. Call (866) 942-7683 with your brand and model.
We offer same-day service on opener calls when you reach us during dispatch hours. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm. At (866) 942-7683.
We stand behind our work, and our technicians have up to 14 years of experience on these systems. Warranty terms on parts and labor are confirmed with you before the work starts, so you know what’s covered. Call (866) 942-7683 and we’ll explain it for your job.
Clear the floor of the garage so we can reach the door and the opener safely, and have any remotes or keypads handy. Note what happens when the door fails: does it hum, reverse, or stay shut? That detail speeds the diagnosis. Call (866) 942-7683 before we arrive.
Schedule Your Garage Door Opener Repair Service in St. Louis Today
A door that won’t open is a problem worth solving today. Call Landon Garage Door Repair at (866) 942-7683 for a free estimate on opener repair, replacement, or a new install. We answer 24/7, and same-day service is available. You’ll get upfront pricing and a written quote before any work starts. One call covers the door and the opener together, with no obligation.
Written by the team at Landon Garage Door Repair.